Vaper's ABCs

Interest in vaping is gradually reaching more and more people. Some are interested in new technologies, others are attracted by fashion trends, while others are trying to get rid of the harmful habit of smoking.

Regardless of vaping experience, every vaper, when first introduced to a gadget, is interested in how to use such a device and how to set up an electronic cigarette in such a way as to ensure high-quality, safe and at the same time pleasant vaping.

Before you figure out how to properly set up an e-cigarette, you need to find out why it is so important to properly organize this process.

An incorrectly configured device will not only not provide high-quality and proper vaping, but can also negatively affect the health of the vaper.

After all, incorrectly adjusted tightening force or the volume of steam that enters the lungs can lead to both unpleasant sensations during vaping and the development of certain diseases of the lungs and respiratory tract. Perhaps this is the greatest danger of an electronic cigarette, the settings of which do not meet the needs of the user.

In addition, an incorrectly configured device can simply break due to overload. If the vaper takes a deep puff and the mod’s power is not enough, the e-cigarette will either immediately fail or, what is much worse, explode right in the user’s hands.

As you can see, you need to set up an electronic cigarette as soon as the vaper is interested in this device as a device for vaping. The safety of the mod user and the quality of vaping depend on the correct adjustment of the device.

First introduction: how to turn on the electronics?

Congratulations, you have become the owner of your first electronic cigarette. Without exaggeration, your life will change in the near future.

What does a vape consist of and how does it work?

In the meantime, you need to make sure that you have everything you need to use your e-cigarette efficiently:

• battery pack;
• clearomizer (atomizer, evaporator, steam generator) - this part is often sold complete with a battery (this kit is called a “starter kit”);
• charger (most chargers are equipped with a standard micro-USB connector);
• bottle with liquid for vaping.

Inexperienced vapers need to pay special attention to the atomizer. If you purchased a Starter Kit, it fits perfectly with the battery pack. If you want to purchase a clearomizer as a separate part of an electronic cigarette, you need to make sure that the type of connector on it matches the type of connector on the battery pack housing of the vaping device.

In addition, it is necessary to find out the possibility of servicing the atomizer (on a serviced evaporator, you can change the winding on your own, while for unserviced ones, you will need to replace the old coil with a new, purchased one).

Don't know how to properly assemble a vaping device? With the help of the following step-by-step instructions, anyone, even an inexperienced vaper, can assemble e-cigarettes on their own:

1. First of all, you need to make sure whether the atomizer is equipped with an evaporator (bowl with a wick).
2. Next you need to fully charge the battery pack.
3. After this, unscrew the atomizer, turn it over and fill it with vaping liquid through a special hole.
4. Finally, you need to install a steam generator filled with liquid on the battery pack.

That's it, your vaping device is fully charged and ready for vaping. It is extremely important to monitor the battery charge level and charge it in a timely manner. Otherwise, the battery pack may fail very quickly.

The charging frequency of an electronic cigarette directly depends on the capacitive characteristics of the battery pack. On average, every 1000 mAh is enough for about three hundred puffs. When the battery pack has a passthrough function, the vaper will be able to vape from it even while charging, without waiting for it to complete.

Setting up the mod to work correctly

This process largely depends on the model of the gadget used. We cannot know what kind of electronic cigarette you are using: a simple miniature “eGoshka” or a multifunctional, modern box mod. But be that as it may, be sure to read the information below on how to set up an electronic cigarette and implement vaping.

Adjusting an e-cigarette involves setting one or several parameters at once:

1. Power supplied to the steam generator (spiral winding).
   The larger the spiral (or the greater the number of spirals), the greater the power required to implement the tightening. The greater the power, the greater the amount of steam and the sooner the battery pack will discharge (the rate at which the battery discharges depends on its power).
2. Varivolt (VariVolt or VV).
   The ability to manually regulate the voltage, and the power depends on the winding resistance of the steam generator. The voltage is directly proportional to the volume of inhaled vapor.
3. VariWatt (VW).
   Possibility of adjusting power when changing resistance. This is a part with the help of which resistance is monitored and, depending on it, the voltage changes. With such a “function” in an electronic cigarette, there is no need to manually adjust the voltage. You just need to set the desired power.
4. Thermal control
   An automatic function that can also be added to an e-cigarette. With the help of this chip, the temperature of the steam generator is monitored, due to which, in fact, its regulation is realized. The presence of thermal control is characterized by a timely decrease or increase in the temperature of the evaporator, which greatly simplifies the use of the device for vaping.

In the first couples, you need to set the voltage based on your taste. To make adjustments, we will use the control buttons located on the battery pack. Experts recommend focusing on the desired amount of steam and ensuring that the liquid in the cartridge does not hiss or burn with a characteristic burnt taste.

Do you also need to be able to soar?

Additional article about vapes.

So, the vaping device is assembled, charged and configured. You can finally try and find out what vaping is like, which makes many people so delighted:

1. Turn on the electronic cigarette. To do this, you need to press the button located on the battery pack. The battery will supply voltage to the spiral winding and after a moment you can already inhale the first puff. True, there are also modern mods that turn on without a button. In such devices, the mechanism is activated when the steamer takes a puff.
2. We hold the electronic cigarette in a vertical position or at an angle with the mouthpiece up. If you hold the device in a horizontal or upside-down position, it will not function at all.
3. If there are small holes on the body of the electronic cigarette intended for air exchange, it is not recommended to close them with your fingers while inhaling. These are incorrect actions that can lead to overheating and damage to the device.
4. The tightening is done simultaneously with pressing the button (this applies exclusively to “push-button” electronic devices and mods).
5. If you have just joined the ranks of vapers and do not know how to inhale steam correctly, then at first it is recommended to take a puff that is not too long (no more than 5 seconds). Between inhaling the vapor from the vape, short pauses are made - about 5 seconds. Let the atomizer cool down. He will thank you for your care with a longer service. In addition, this approach will ensure timely cooling of the coil and, thereby, prevent its overheating.
6. You need to tighten it smoothly. Vaping differs from regular smoking, which is why it is not recommended to take several puffs at once without a pause. Failure to follow this recommendation will result in liquid leakage through the steam generator and overheating of the coil.
7. When you are finished vaping, be sure to lock your e-cigarette before putting it in your pocket or bag. The locking method, as a rule, consists of pressing the button five times (although locking a gadget largely depends on its model and on the settings that were provided by the manufacturer).

Let's talk more about the advantages of vaping over smoking.

So, the first experience has been successfully obtained, the device has passed the first test, and you are ready to actively continue learning the basics of vaping.

When vaping, you should stick to the same intensity as when smoking regular cigarettes. Simply put, experienced vapers, as well as experts in the field, do not recommend taking more than 20 puffs at a time. The e-cigarette has no end, so in the early stages of the debate, an overdose of nicotine substances present in the vaping liquid is especially dangerous.

It is recommended to take breaks between cigarette breaks throughout the day. If used too often, the storage tank will dry out very quickly in the part that comes into contact with the steam generator. During a break of an hour or two, the liquid has time to be evenly distributed throughout the cartridge.

If you can’t stand such long breaks, you can purchase a replacement cartridge. By the way, it will also be useful to the vaper when the vaper wants to change the taste of the liquid or its strength.

After all, there is always a little underused liquid left in the evaporator, so when using a new e-liquid of a different flavor, they will mix, which will not have the best effect on the taste of the vapor.

The most appropriate way to avoid this precedent is to use a separate clearomizer for each flavor.

Vaping with pleasure

If you do not take a powerful, but long-lasting inhalation of steam, it will flow abundantly into the lungs. While too deep or sharp puffs can lead to the formation of excess fluid in the clearomizer, which can leak through the threads into the battery pack. Hence the malfunction of the gadget and, as a result, its breakdown.

In addition, many models, when taking strong and sharp puffs, begin to emit sounds uncharacteristic for this process: whistling, hissing. Do you need some extra noise? Thanks to long puffs, a large volume of steam enters the lung cavity, which means that saturation will occur much faster than with small and abrupt puffs.

It is advisable to tilt the device for vaping slightly downward, then the liquid from the storage tank will flow into the steam generator gradually and evenly.

Experts strongly recommend monitoring the amount of liquid in the cartridge. It is highly undesirable to allow the filler to be empty during tightening. This may cause the wick to overheat and break. But at the same time, it is also not recommended to fill the e-liquid above the required level; this entails a leakage of the atomizer.

In addition, the steam generator of an electronic cigarette needs regular cleaning (at least once a month). This procedure is not complicated and can be easily organized at home without the involvement of more experienced vapers.

It is enough just to disassemble the upper part of the device into its components and rinse the winding, bowl, wick, cartridge under running heat
oh water. In case of serious contamination, you can wash the parts of the electronic cigarette in an alcohol solution. But it’s better not to run the state of your gadget.

The frequency of replacing the atomizer mainly depends on the intensity of use of the vaping device. As a rule, experienced vapers change their vapor generator 1-2 times a month.

In addition, there are several rules that are considered good manners among vapers. For example, it is prohibited to leave an electronic cigarette unattended in the presence of children. And you can soar among people only with the consent of others. Taking a puff from a vape while driving a vehicle is dangerous and not entirely wise. In a word, all the advice offered by experts and experienced vapers is quite logical and understandable without unnecessary reminders.

By following the rules for using a vaping device described above, you can significantly extend the life of the device. Proper vaping is more reminiscent of smoking a hookah than a regular cigarette. So just try it, learn how to use an electronic cigarette and enjoy vaping. Soar with pleasure!

A complete cigarette, from scratch - from the evaporator to the quick connection of the battery with the atomizer
(and: the evaporator design is improved, including a battery charger) - using available components.

I have been using this design for quite a long time and can fully recommend it to everyone who wants to quit smoking tobacco cigarettes!
Personally, I haven’t smoked a single tobacco cigarette for almost four years!!! And I did it calmly, without any discomfort. The result is that the cough has completely gone away and now I’m even annoyed by the smell of tobacco smoke (this is after 45 years of smoking experience!). I can afford to “float” in my apartment: bedroom and in any other room, without causing any inconvenience to others at all! I made two options: home and pocket (outdoor) options, and during this time I did not find any “leaks” that users of branded atomizers (evaporators, which are far from cheap) write about.

The device does not include any scarce components and only requires care during manufacturing and further
handling it.

Materials and components:

1. Nichrome wire diameter - 0.15 mm.
2. Silica cord diameter - 2 mm. (I order nichrome and cord from the online store of electronic cigarettes "Pipiroska")
3. Syringe 20 ml.
4. 3 ml syringe. 4a - finished atomizer body from this syringe.
5. Cap from a disposable e-cigarette "PONS".
6. The tube from the indoor telescopic antenna has a diameter of 2.5 mm.
7-8. Rubber inserts.
9. The tube from the indoor telescopic antenna has a diameter of 4.5 mm.
10. A piece of power cable. Outer diameter of insulation: 4.2…. 4.5 mm.
11. Contact plate from an electromagnetic relay or any other suitable elastic plate.
12. Orthophosphoric acid.
13. The body of the disposable e-cigarette "PONS" (metal).
14. Rubber of a car inner tube with a thickness of 3....3.5 mm.
15. Collapsible plug "Tulip".
16. Collapsible plug "Tulip" (socket).
17. Battery size 18650 (U= 3.6….4.2 v.)
18. To assemble the atomizer: 3 ml syringe piston holder rod. and a ballpoint pen body, outer diameter - 8 mm.
19. Syringe for refilling (any).
20. Glue "Moment"
21. HB thread.

Photo 1 The most complex part of an electronic cigarette is the atomizer (evaporator). Let's start with him.
We make the body from a 3ml medical syringe. We cut it on both sides so that the length is approximately 55 mm. We carefully process the sections, wash off the applied marks (by the way, they are easily washed off with diesel fuel).

Photo 2 Using the sharpened edge of the body of a disposable cigarette "PONS" we cut out two inserts from the rubber of the car inner tube.

Photo 3 Using a tube from a telescopic antenna with a diameter of 4.5 mm, we cut out the central holes on both inserts, and on one of them we pierce two holes with a syringe needle for the leads of soft conductors from the heater.

Photo 4 From the same tube we make a central air duct about 35 mm long. On one side we make a figured cutout shaped like a keyhole.

Photo 5 The heater is a nichrome wire with a diameter of 0.15 mm, the ends of which are wound and soldered to soft stranded conductors with phosphoric acid. The working section of the heater must be 26 mm long. (selected empirically).

Photo 6 Carefully wrap it around the silica cord.

Photo 7 We pass the ends of the bends into the punctured holes of the liner and stretch them to the base. We cut off the remaining cord around the circumference of the liner. Then (this is important!) with a syringe needle we “ruffle” the edges of the cord near the soldered contacts so that the fibers in these areas are on top of the nichrome winding. If we do everything carefully and correctly, then when the brass tube of the air duct is seated, it will not “short-circuit” the heater coil. Silica is an excellent insulator!

Photo 8 Now carefully insert the tube into the insert. I would like to note that this process requires accuracy and a certain skill.
I’ll be honest: I didn’t succeed the first time!

Photo 9 After this, you must check this area with the device. If we did everything “cleanly”, then the resistance should be
1.8….2.0 Ohm.

Photo 10 Now we assemble the other end of the tube. Remove a piece of insulation from the power wire. Its outer diameter should be 4.3...4.5 mm.
We insert it about halfway into the tube (it should fit quite tightly), and put the second liner on the remaining part.
This is done so that when inserting the assembled structure into the atomizer body, the liner does not “slide” along the tube.

Photo 11 We insert the assembled assembly into the body of the former syringe. To facilitate this process, it is better to lubricate the circumference of the liners with refilling liquid.

Photo 12 When inserting, it is better to apply pressure on the central part, where the edge of the shaped cutout of the tube is located. To do this, you can use the piston rod from the same syringe with side slots for the exit of soft conductors.

Photo 13 Drill an air hole with a diameter of 1...1.5 mm,

Photo 14 We solder the leads of the conductors to the “Tulip” plug, having first shortened the “negative” lead,

Photo 15 We put on the cap from “PONS” on the “mouthpiece” side, cutting a hole with a diameter of 1.5…2.5 mm in the center and the atomizer is ready.

Photo 16 Now the power supply block. At the “Tulip” connector socket, we completely remove the negative terminal.

Photo 17 We solder the positive terminal of the connector to the positive contact of the battery, as accurately as possible in the center (for aesthetic reasons). Be careful not to short-circuit it to the battery negative! Nearby is the edge of the body (minus).

Photo 18 Since the positive terminal of the connector does not have high mechanical strength, I do this. I wrap the already soldered terminal with cotton thread quite tightly, periodically lubricating the area with Moment glue until it is filled, until the winding is equal in diameter to the threaded part of the connector.

Photo 19 Our switching will be carried out via the negative circuit. Therefore, I chose the simplest and most reliable method.
We solder a springy brass strip to the battery body. Since it is made of iron, it must be soldered with phosphoric acid. Then we cut the strip and make a bend in such a way that when you press it, it ensures reliable contact with the outer cup of the inserted atomizer.

Photo 20 For appearance, you can wrap it with adhesive decorative film or use heat-shrink tubing with a diameter of 20 mm.

Reading time: 4 minutes.

Every vaper sooner or later has to face such a task as repairing electronic cigarettes. Often you can repair a device yourself, but first you need to familiarize yourself with its structure.

Design

So what parts are included in a vape? An electronic cigarette has a vaporizer (atomizer) and a battery pack (mod). The atomizer supplies liquid to the heating element (in most cases a coil) through a special cotton wick. Vaporizers come in several types and vary in capacity, amount of vapor, flavor potential, and ease of maintenance. It should also be noted that a number of types are classified as maintenance-free. They do not require the user to independently replace the wick and rewind the coil and require the purchase of consumables.

The evaporator is connected by a thread to a battery pack, which is responsible for powering the atomizer with electric current. The battery can be either built into the mod or replaceable. The mods themselves can be divided into two main types: mechanical and VV/VW. In the first case, a voltage-controlling microcircuit is not used and the current is supplied directly to the heater; in the second, the user can control the voltage through the microcircuit. Functionally, battery packs differ in capacity, presence of charge indication, type of control and a number of additional functions. What to do if the electronic cigarette does not work? Let's consider possible ways to troubleshoot the problem.

Problems and solutions

The list of the most common problems with an electronic cigarette looks like this: the cigarette has stopped working (“does not smoke”), the quality of the vapor has become worse, the amount of vapor has decreased. Practice shows that in such cases the electronic cigarette evaporator needs to be repaired.

1. It is necessary to unwind the vape, thus separating the atomizer from the mod.
2. We disassemble the evaporator to remove the coil and cotton wool.
3. If there is carbon deposits on the spiral, you need to get rid of it. It will be much easier to do this by pre-warming it on gas.
4. We replace the cotton wool with a new one and carefully put the evaporator back together.
5. We connect the mod and the atomizer and check the result.

If, when disassembling the evaporator, you find a broken element (for example, a spiral), then it will have to be replaced. If the electronic cigarette does not unwind at all, you will have to clean or lubricate the threads. But the vaporizer is not always the only reason why an e-cigarette does not work.

Why doesn't the device work even though all the above steps have been done? Perhaps the problem lies in the battery pack. If you do not monitor the condition of the battery, it may fail. When your e-cigarette flashes, it indicates that the battery is running low (unless the flashing occurs when the atomizer is connected: it could be broken, try replacing it).

Read also: Let's figure out how to make more vapor in an electronic cigarette

If you encounter power problems, you may have to replace your entire mod if the battery is not removable and/or the electronics are burned out, or you may have to change the battery or chip individually. You will need to spin up the device. You will not be able to repair the battery yourself, and it has no practical meaning.

If everything is fine with the atomizer, the battery is charging, and the operation indicators are functioning, the problem lies in the mod's chip. Unwind the vape, disassemble the battery pack and check if the microcircuit contacts have come loose.

It is worth adding that an electronic cigarette may stop “vaping” when there is no contact between the atomizer and the unit. Always make sure the threads are fully tightened.

Sometimes the vape can experience leaks, short circuits, and other minor failures that can cause the device to malfunction. Luckily, there are a couple of simple methods you should try every time before attempting to fix your e-cigarette yourself.

In recent years, electronic cigarettes have ceased to be just a means of replacing tobacco smoking. Today, vaping is an entire subculture, whose adherents are passionate, first of all, about original tastes and obtaining abundant vapor. The last question often becomes a problem, because not all devices are able to please users with rich steam generation. Let's figure out how to fix this.

There are several reasons that determine why there is little smoke in an electronic cigarette.

Low battery

If the battery charge shows only ten percent, the amount of vapor decreases due to a lack of voltage on the coil. In this case, you need to charge the battery.

Incorrect tightening

An electronic cigarette differs from a regular cigarette in the intensity of vaping. For a sufficient amount of steam, it is necessary to take longer and smoother puffs, single and measured. This is necessary so that the liquid falling on the coil evaporates. If the puffs are short or double, you will end up with an excess of liquid in the atomizer.

This use may also cause the threads of the e-cigarette to leak. Evaporation occurs well in the new atomizer after “breaking in” (after five to ten puffs).

Atomizer clogged

This occurs due to an excess of liquid, which has a bad effect on the operation of the atomizer. It will be enough to blow it out, thereby eliminating excess liquid. At the same time, it is necessary that the atomizer always has a small amount of liquid to prevent burning of the wick, which conducts the liquid to the filament. After blowing out the atomizer, you need to take one or two puffs without pressing the button.

In an ES with an automatic battery, you do not need to screw the atomizer to the battery, but you need to close the hole on the atomizer connector with your finger.

There is no liquid in the cartridge

Check if there is liquid in the cartridge. If it is missing or not enough, fill it up. You can increase the service life if you monitor the level and presence of liquid in the cartridge.

Great wear

Maybe the atomizer has been used for a very long time and needs to be changed. An atomizer is an ES consumable. As you know, the service life of this part is approximately 1-2 months.

The duration of the term is influenced by many factors:

• specifications;
• correct operation;
• smoking intensity.

How to make more vapor in an e-cigarette

There are ways to make more smoke from an e-cigarette. First of all, you need to develop your own puffing smoking technique. This comes with experience. The production of equipment must take place on a working electronic cigarette with a refilled cartridge. First, fix technical problems, then practice.

Glycerol

Glycerin is often used to increase the amount of steam. It is added to the ES fluid. You can buy glycerin both in a regular pharmacy and in specialized stores that sell electronic cigarettes. In the pharmacy, the cost of this substance is much less, you just need to choose glycerin that is suitable for food use. Vegetable glycerin can be found in the cough syrup section of the pharmacy. It will be enough to add just a few drops of glycerin to noticeably increase the amount of steam.

Hand batteries

When automatic batteries are used, the atomizer heats up first. At this point no smoke is produced. The manual battery works immediately after pressing the button. Usually, owners of a manual battery have an advantage, since when using automatic ones, you can only inhale smoke when the atomizer is hot.

Stability of liquid supply to the atomizer

Only with a stable supply of liquid to the atomizer is good vapor produced. Quite often the cartridges are poorly refilled. Because of this, the liquid does not enter the atomizer bridge. To get good smoke you need to keep the cartridges filled.

Freshly charged batteries

When the battery has just been charged, it produces more voltage, which increases the amount of vapor and the strength of the “throat hit”.

High battery voltage

At higher voltage the quality of steam is higher. Standard batteries have a voltage of approximately 3.7 Volts. With these batteries, the cartridge can withstand a voltage of 3-5 volts, but at 7 volts it can burn out. Non-standard batteries have a voltage from 3 to 7 Volts. The disadvantage of high voltage is the disappearance of the primary aroma of the ES liquid.

Low resistance of the atomizer

A lot of vapor from an electronic cigarette is released if the atomizer has little resistance. This is due to the higher heating rate. But this has a drawback - the battery discharges faster and the ES fluid runs out. In this case, the primary aroma may disappear to a small extent. The most popular low resistance atomizer is the 510 1.8 ohm atomizer.

Variety of liquids

The quality of vapor depends on the chemical composition, aroma and concentration of nicotine in the liquid. It is recommended to try different types of liquids. For example, adding menthol to a liquid transforms the vapor into a thicker one and enhances the “throat hit”.

Long battery life

To create an electronic cigarette that is most similar to a real one, it is made in small sizes. Consequently, the charge runs out very quickly and the amount of vapor is usually small. There are electronic cigarettes with increased weight and volume. They have large battery sizes. These cigarettes hold a charge longer. Such batteries last at least 1 day.

Overview of ES with a lot of steam

It is worth highlighting a number of models capable of producing a lot of steam.

SLB DSE-601

Perhaps this is the first model that can be noted. Its difference from others is in the battery power and cartridge capacity. This model is suitable as a gift, as it has a stylish appearance and original design.

Joye eGo-T Mega

This is a different, less expensive model. Despite its modest appearance, it allows you to get a large amount of steam. In addition, this device comes with all the attributes necessary for smoking.

New Life

It also allows you to get a large amount of smoke. Its external characteristics are more suitable for girls. This e-cigarette has a glamorous look and also an advantage in terms of technical characteristics. The E-cigarette has a capacious battery with a capacity of 1950 mAh.

Denshi Tabaco Turbo Premium

This model is suitable for you if you need an ES with a large amount of steam. This ES attracts with its stylish appearance, richness and density of smoke, which is achieved thanks to more advanced cartridges that are equipped with built-in steam generators.

The main thing is to have a charged, working electronic cigarette with you. For a comfortable transition to ES, it is recommended to use a stronger liquid for smoking at first. You can gradually reduce the strength. It is recommended that you eventually switch to 0 mg nicotine pacifiers, which act as a “placebo.” This technique has a very good effect on health - it reduces the frequency of coughing.

Video

From our video you will learn how to quickly and easily increase the amount of vapor in an electronic cigarette.

Reading time: 4 minutes. Published 12/06/2017

Despite the fact that Ijust appeared on the vaping market relatively recently, it is quickly gaining popularity among vapers, whether a beginner or an experienced vaper. But, no matter how ideal this electronic cigarette is, you always want to improve it, make it more attractive. Let's see what upgrade can be made to this e-cigarette.

What kind of electronics are installed

The electronic cigarette of the ijust s brand is equipped with two types of protection, the first protects the electronic cigarette from possible overcharging of the battery or, on the contrary, maximum discharge. The second type of protection is against possible short circuit. So from this side you are completely protected.

As for the voltage supply, it remains similar to its predecessor Aijast 2, and is supplied directly from the battery to the evaporator.

In this regard, it should be noted that the strength and intensity of vaping depends entirely on the full charge of the battery. The latter can be controlled using a special light sensor, which engineers placed under the “on/off” button of the device. The second indicator is located under the connector for connecting a USB charger; it lights up all the time while the cigarette is charging.

As you can see, the absence of an OLED information display does not in any way affect the ability to control the functioning of this vape device.

What is the best way to reflash this electronic cigarette?

Reflashing an electronic cigarette can be carried out both in a specialized vape salon and at home. Note that the second option is not complicated and you can easily do it yourself.

You will need a special program to modify the software of your device. You can find such software on specialized websites; in most cases, the necessary content is downloaded for free.

The firmware procedure consists of several stages:

• connecting a cigarette to a PC using an additional cable;
• downloading the program for the brand you need. Often this is an archived version of the software;
• installing the required update after unzipping the file.

It is worth noting that there are two versions of the Ajast s firmware - Chinese (CN) and European (ROW).

How to make a mech mod from ijust s?

A mechanical mod or mechanical mod (battery) is a hollow metal tube, the main task of which is to close the contacts between the e-cigarette atomizer and the battery. Considering that there are no electronics in it, the amount of vapor produced by your vape depends entirely on the resistance of the atomizer.

If the board on the device fails, you can give the vape a “second life” and tune the ijust s , replacing electronics with mechanics.

Can this model be improved?

Modernization of Agest s can be carried out using several methods. First of all, if you are not satisfied with the amount of steam produced, replace the atomizer with one with a lower resistance, there will be more steam, but the taste of the vaping liquid may suffer and the charge in the battery will run out faster.

Secondly, you can replace the battery itself with a more powerful one, but take into account the capabilities of your vape, otherwise it will simply burn out. Alternatively, you can use a battery with a large reserve capacity.

If the desire to upgrade your electronic cigarette with the first two options has not dried up, try replacing the electronic battery with a manual or mechanical one. The advantage of the latter is that the cigarette begins to vapor immediately after activation, unlike automatic ones, where it takes time to warm up the atomizer.

A partial option for improving Ijast s would be to wind an additional spiral, which will increase the area of ​​contact with the liquid. If you don’t want to make mechanical changes to your vape, try switching the vaping liquid you use to one with a high percentage of glycerin.

There are many opportunities to make a better vape Ajust with - just choose the best one for you and enjoy!